headers
Izumi Tsutsui | 30 Apr 2009 04:04
Picon
Gravatar

5.0 on hp425t

Just FYI,

---
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0 (GENERIC) #0: Sun Apr 26 16:25:34 UTC 2009
	builds <at> b0.netbsd.org:/home/builds/ab/netbsd-5-0-RELEASE/hp300/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/src/sys/arch/hp300/compile/GENERIC
HP 9000/425t (25MHz MC68040 CPU+MMU+FPU, 4k on-chip physical I/D caches)
total memory = 49140 KB
avail memory = 43488 KB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
frodo0 at intio0 addr 0x41c000 ipl 5
dnkbd at frodo0 offset 0x0 not configured
com1 at frodo0 offset 0x40: ns8250 or ns16450, no fifo
com2 at frodo0 offset 0x60: ns8250 or ns16450, no fifo
hil0 at intio0 addr 0x428000 ipl 1
nhpib1 at intio0 addr 0x478000 ipl 3: internal HP-IB
hpibbus1 at nhpib1
dma0 at intio0 addr 0x500000 ipl 1: 98620C, 2 channels, 32-bit DMA
dio0 at mainbus0
com0 at dio0 scode 9 ipl 5: ns16550a, working fifo
internal parallel at dio0 scode 12 ipl 3 not configured
spc0 at dio0 scode 14 ipl 4: 98265A SCSI, 32-bit DMA, SCSI ID 7
(Continue reading)

Permalink | Reply |
headers
Izumi Tsutsui | 30 Apr 2009 06:30
Picon
Gravatar

5.0 on hp382

I receive a question about 375 and 380, but I only have 382 and 425t.

040 models should also work, but there have been very few reports
about 020/030 models for long years so there might be some botches
on those machines.

Note the GENERIC kernel may require at least 8MB memory
because GENERIC itself is ~3.3MB. For 4MB machines
you might have to build a custom shrinked kernel.

Any tests/reports are appreciated :-)

---
 Self-Test Mode
Copyright 1991,
Hewlett-Packard Company.
All Rights Reserved.

BOOTROM  Rev. 3.01  2 MAY 91
MC68040 Processor
Configuration EEPROM
Utility Chip at 41
HP-HIL
 RESET To Restart
 Self-Test Mode
HP-IB
DMA-C0
 Self-Test Mode
RAM 25165482 Bytes
HP98624 (HP-IB) at 8
(Continue reading)

Permalink | Reply |
headers
doomwarrior | 1 May 2009 15:42
Picon

Re: 5.0 on hp382

Hi,

huh dmesg pr0n? I'm in :-)
My system is a 400t with a 030. Not heavly tested but seems to work OK, 
like 3.X which was installed before.

Boot: [[[sd3a:]netbsd][-a][-c][-d][-s][-v][-q]] :-
1113340+29108+201248 [253792+130156]=0x1a7fcc
Start  <at>  0xfc803400 [1=0xfc94c0d4-0x1a7fcc]...
Entry point: 0xfc803400
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.

NetBSD 5.0 (INSTALL) #0: Sun Apr 26 16:27:44 UTC 2009
builds <at> b0.netbsd.org:/home/builds/ab/netbsd-5-0-RELEASE/hp300/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/srL
HP 9000/400 (50MHz MC68030 CPU+MMU, 50MHz MC68882 FPU, 32K 
physical-address cache)
total memory = 57332 KB
avail memory = 53664 KB
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
frodo0 at intio0 addr 0x41c000 ipl 5
dnkbd at frodo0 offset 0x0 not configured
com0 at frodo0 offset 0x40: ns8250 or ns16450, no fifo
com1 at frodo0 offset 0x60: ns8250 or ns16450, no fifo
hil0 at intio0 addr 0x428000 ipl 1
(Continue reading)

Permalink | Reply |
headers
doomwarrior | 1 May 2009 16:01
Picon

5.0 install with CD

Hi,

Installing from a miniroot installed on swap. It was not possible to 
select packages from cd. The scsi-cd0 was found at boot time and it was 
possible to mount the cdrom and copy data from it. I'm wondering why the 
install script couldn't find any sets on the NetBSD 5.0 hp300.iso?

Best Regards
Stephan
Permalink | Reply |
headers
Izumi Tsutsui | 3 May 2009 15:44
Picon
Gravatar

Re: 5.0 install with CD

doomwarriorx <at> gmail.com wrote:

> Installing from a miniroot installed on swap. It was not possible to 
> select packages from cd. The scsi-cd0 was found at boot time and it was 
> possible to mount the cdrom and copy data from it. I'm wondering why the 
> install script couldn't find any sets on the NetBSD 5.0 hp300.iso?

Hmm, no one has tried miniroot installation since MI SCSI migration?
(sysinst based netbsd-RAMDISK kernel is easier to install)

Could you please the following change?
I guess you can edit /install.md on miniroot environment.

---
Index: install.md
===================================================================
RCS file: /cvsroot/src/distrib/hp300/miniroot/install.md,v
retrieving revision 1.13
diff -u -r1.13 install.md
--- install.md	30 Apr 2008 13:10:48 -0000	1.13
+++ install.md	3 May 2009 13:41:52 -0000
 <at>  <at>  -75,7 +75,7  <at>  <at> 

 md_get_cddevs() {
 	# return available CD-ROM devices
-	dmesg | awk -F : '/^cd[0-9]*:.*cdrom/ { print $1; }' | sort -u
+	dmesg | awk -F : '/^cd[0-9]*:/ { print $1; }' | sort -u
 }

 md_get_ifdevs() {
(Continue reading)

Permalink | Reply |
headers
doomwarrior | 4 May 2009 19:05
Picon

Re: 5.0 install with CD


Izumi Tsutsui schrieb:
> doomwarriorx <at> gmail.com wrote:
>
>   
>> Installing from a miniroot installed on swap. It was not possible to 
>> select packages from cd. The scsi-cd0 was found at boot time and it was 
>> possible to mount the cdrom and copy data from it. I'm wondering why the 
>> install script couldn't find any sets on the NetBSD 5.0 hp300.iso?
>>     
>
> Hmm, no one has tried miniroot installation since MI SCSI migration?
> (sysinst based netbsd-RAMDISK kernel is easier to install)
>
>   
I couldn't follow your notice. I have done the installation according to 
the Installation notes
> Could you please the following change?
> I guess you can edit /install.md on miniroot environment.
>   
no that is sadly not possible. But I have entered both commands in the 
shell:

# dmesg | awk -F : '/^cd[0-9]*:.*cdrom/ { print $1; }' | sort -u
# dmesg | awk -F : '/^cd[0-9]*:/ { print $1; }' | sort -u
cd0
#

That is an improvement :-)
(Continue reading)

Permalink | Reply |

Gmane